manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 677

Maintenance

Power Blazer

665

Recalibrating the Unit

Recalibrating the Unit 

EXFO manufacturing and service center calibrations are based on the 
ISO/IEC 17025 standard (

General Requirements for the Competence of 

Testing and Calibration Laboratories

). This standard states that calibration 

documents must not contain a calibration interval and that the user is 
responsible for determining the re-calibration date according to the actual 
use of the instrument.

The validity of specifications depends on operating conditions. For 
example, the calibration validity period can be longer or shorter depending 
on the intensity of use, environmental conditions and unit maintenance, as 
well as the specific requirements for your application. All of these elements 
must be taken into consideration when determining the appropriate 
calibration interval of this particular EXFO unit.

Under normal use, the recommended interval for your module is: 2 years.

For newly delivered units, EXFO has determined that the storage of this 
product for up to six months between calibration and shipment does not 
affect its performance (EXFO Policy PL-03).

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands