manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 610

Test Functions

598

88000 Series

OH - SONET/SDH

STS/AU/TU-3 

J1

: Trace. Available when the Trace format is set to 1 Byte (refer to 

Traces (SONET/SDH)

 on page 336). 

SONET: The J1 Trace byte provides a 16 or 64 byte fixed string to verify 
connection between path transmitting equipment and path receiving 
equipment. 

SDH: The higher-order (AU)/low-order (TU) VC-N path trace byte 
provides a 64 byte fixed string to verify connection between path 
transmitting equipment and path receiving equipment.

B3

: BIP-8. The BIP-8 (Bit-Interleaved Parity) byte provides path error 

monitoring. The byte is calculated by performing a even-parity check 
over all bits of the previous SPE. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands