manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 529

Test Results

Power Blazer

517

Summary (TCP Throughput)

TCP Throughput

TCP Connection Status

 indicates the actual TCP connection status. 

Transmitted Frames

 indicates the total of frames transmitted by the 

local unit excluding the re-transmitted frames. 

Re-transmitted Frames

 indicates the total of frames that have been 

re-transmitted by the local unit. 

Efficiency (%)

 indicates the percentage of bytes that were not 

retransmitted. 

Window Size Unit

 allows selecting the unit used for 

Window Size

: 

Bytes

, 

KBytes

, or 

MBytes

 (default). 

Throughput Threshold 

allows setting the pass/fail verdict threshold 

value: 

0

to

100 %

(default). This setting is available when the 

Throughput Pass/Fail Verdict

 check box is selected (refer to 

TCP 

Throughput

 on page 327). 

Throughput

 meter displays the last second TCP Throughput 

measurement. 

Test Status

Description

“--” 

The test is not running or results are not available.

In Progress

The TCP initialization algorithm is in progress.

Waiting

 Indicates on the remote unit that the test is started but the 
TCP initialization algorithm is not initiated by the local unit.

Established

The TCP session has been successfully established between the 
local and remote units.

Closed

The session is closed. Either no TCP initialization algorithm has 
been received, the remote unit has received and completed the 
request to close the TCP session, or no data has been received 
at the remote unit for 30 seconds.

Closing

The TCP protocol is closing down the connection.

Remote IP not found

The local unit didn’t received an answer to the ARP request sent 
to the IP address of the remote unit.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands