manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 516

Test Results

504

88000 Series

Summary (RFC 2544)

Unit

: Select the subtest result unit: 

For Throughput: 

Mbit/s

, 

Gbit/s

, 

frame/s

, and 

%

. 

For Back-to-Back: 

Mbit/s

, 

Gbit/s

, 

frame/burst

, and 

%

. 

Frame Loss: 

%

. 

Latency: 

ms

, and 

μ

s

. 

Layer

: For Throughput and Back-to-Back subtests, select the 

subtest layers used to calculate the throughput. 

All

 (default): Layer 1,2,3 contains the Idle, Preamble, Start of Frame 

Delimiter, MAC address, IP address, and data. 

Ethernet

: Layer 2,3 contains the MAC layer, IP layer, and data. 

IP

: Layer 3 contains the IP layer, and data.

Step

: For Frame Loss subtest, selects the step (%) of the testing 

rate to be displayed. 

Mode

: For Latency subtest, selects the propagation time mode. 

Cut Through

 (default) allows the calculation of the propagation 

time of a bit (Bit Latency). 

S. & F.

 (Store and Forward) allows the calculation of the 

propagation time of a frame (Frame Latency). 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands