manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 450

Test Results

438

88000 Series

OTL-SDT

Longest Disruption

 indicates the longest measured disruption time. 

Lanes with Disruption

 indicates the number of lanes with service 

disruption. 

Note:

When a disruption event is equal or longer than the test period which is 
fixed to 5 minutes, then the measured disruption time is equal to the test 
period.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands