manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 399

Test Results

Power Blazer

387

Alarms/Errors Overview

LOF

 (Loss of Frame) 

RX

: OOF is present for at least 3 ms.

TX

: Generates error in all FAS bits continuously.

LOM

 (Loss Of Multiframe) 

RX

: OOM is present for at least 3 ms

TX

: Generates error in MFAS bits continuously.

OOF

 (Out-Of-Frame) 

RX

: FAS (bytes 3, 4, and 5) are in error for at least 5 consecutive OTU 

frames.

TX

: Generates error in all FAS bits for 5 consecutive OTU frames.

OOM

 (Out-Of-Multiframe) 

RX

: MFAS are in error for at least 5 consecutive OTU frames.

TX

: Generates error in multiframe number for 5 consecutive OTU 

frames.

TIM

 (Trace Identifier Mismatch) 

RX

: Expected SM SAPI and/or SM DAPI do not match the received SM 

SAPI and/or DAPI for at least 3 consecutive TTI. This alarm is only 
available when the Enable TIM SAPI OTU-TIM and/or DAPI OTU-TIM 
check boxes are selected from page 337. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands