manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 379

Test Results

Power Blazer

367

Alarms/Errors Overview

Error 

Symbol

 (FC 1X/2X/4X/8X) 

RX/TX

: Invalid code-group is detected/generated in the code. 

Block

 (FC 10X/16X) 

RX

: The number of frames received with an errored block condition.

FCS

 (Frame Check Sequence) 

RX

: Frames with an invalid FCS are received. 

Oversize

 

RX

: The number of received FL-2 frames larger than 2148 bytes with a 

valid FCS. 

Undersize 

RX

: FL-2 frames smaller than 36 bytes with a valid FCS. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands