manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 373

Test Results

Power Blazer

361

Alarms/Errors Overview

Oversize

 (available when the 

Oversize Monitoring

 check box is 

selected.) 

RX

: Frames larger than 1518 bytes

2

 with a valid FCS; 1534 bytes

3

 for 

EoE; 1536 bytes

4

 for PBB-TE. 

Runt 

RX

: Frames smaller than 64 bytes with an invalid FCS; 80 bytes for EoE; 

82 bytes for PBB-TE. 

Undersize 

RX

: Frames smaller than 64 bytes with a valid FCS; 80 bytes for EoE; 82 

bytes for PBB-TE. 

Oversize Monitoring

 check box, when selected (cleared by default), 

allows monitoring the 

Oversize

 frame errors. 

The following errors are only available with 

Half Duplex

 mode (only for 

electrical interface at speeds of 10 Mbit/s and 100 Mbit/s). 

Collision

 

RX

: Indicates the number of collisions on the link. 

Late Coll. 

RX

: Indicates the number of collisions that have occurred after a 64 

bytes transmission.

Exc. Coll. 

RX

: Indicates the number of frames that were sent 16 times 

unsuccessfully due to consecutive collisions.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands