manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 370

Test Results

358

88000 Series

Alarms/Errors Overview

E4 

Alarms

Note:

Only AIS is available when the framing is set to Unframed.

AIS

 (Alarm Indication Signal) 

RX

: An unframed all-ones signal is received. 

LOF

 (Loss Of Frame) 

RX

: Four consecutive incorrect frame alignment signals is received. 

RAI 

(Remote Alarm Indication) 

RX

: Bit 13 of a framed E4 is set to “1”. 

Errors

FAS

 (Frame Alignment Signal) 

RX

: Bits 1 to 12 of the first frame differ from 111110100000. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands