manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 221

Test Setup - Test Configurator, Timer, and System

Power Blazer

209

MAC/IP/UDP

PBB-TE 

Note:

Available when PBB-TE is selected as the Provider Encapsulation (see 

Modify Frame Structure

 on page 205). 

Source B-MAC Address

 indicates and allows changing (when the 

Factory Default

 check box is cleared) the default source Backbone 

MAC address: 

00:03:01:xx:xx:xx

. 

Destination B-MAC Address

 allows entering the destination Backbone 

MAC address. The default setting is 

00:00:00:00:00:00

. 

B-VLAN

 (EtherType: 0x88A8) is available when PBB-TE VLAN check 

box is selected (see Modify Frame Structure

 on page 205

). 

VLAN ID

 choices are 

0

 through 

4095

 (default is 

2

). Rrefer to 

VLAN 

ID and Priority

 on page 758 for more information. 

Priority

 choices are 

0

 (default) to 

7

. Refer to 

VLAN ID and Priority

 

on page 758 for more information. 

Drop Eligible

:, when set to 

Yes

 (DEI = 1), the transmitted frames 

will be dropped first on receipt when congestion occurs under test. 
This parameter is set to 

No

 by default. 

I-TAG

 (EtherType: 0x88E7) 

SID

 (Service Instance Identifier) choices are 

0

 through 

16777215

 

(default is 

256

). 

Priority

, the Priority Code Point (PCP), choices are 

0

 (default) to 

7

. 

Refer to 

VLAN ID and Priority

 on page 758 for more information. 

Drop Eligible

:, when set to 

Yes

 (DEI = 1), the transmitted frames 

will be dropped first on receipt when congestion occurs under test. 
This parameter is set to 

No

 by default. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands