manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 209

Test Setup - Test Configurator, Timer, and System

Power Blazer

197

Labels

PLM-V/UNEQ-V / LP-PLM/LP-UNEQ

: Enables the Payload Mismatch 

and VT/TU UNEQ monitoring. This setting is coupled with the 
configuration on the 

Labels

 on page 427. 

Expected

: Select the expected V5 byte from the list. Refer to V5 on 

page 602 for more information. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands