manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 174

Test Setup - Test Configurator, Timer, and System

162

88000 Series

EtherBERT, FC BERT, BERT (CPRI/OBSAI), and Unframed BERT

Note:

The following frame parameters are only available for OTN BERT test 
application with Ethernet client (EoOTN).

Source MAC Address

 is the module default and unique Source Media 

Access Control (MAC) address that is automatically given to the 
stream. Tap the 

Source MAC Address

 field if the stream MAC address 

has to be changed and enter the new MAC address. 

Destination MAC Address

 is the destination MAC address for the 

stream. The default setting is the MAC address of the port. Tap the 

Destination MAC Address

 field if the stream MAC address has to be 

changed and enter the new MAC address. 

VLAN ID

 check box, when selected (cleared by default), allows the 

configuration of the following VLAN parameters. Selecting the VLAN 
check box affects the 

Frame Size

 value. 

VLAN ID

 sets the VLAN ID. Choices are 

0

 through 

4095

 (default 

is

2

). Refer to 

VLAN ID and Priority

 on page 758 for more 

information. 

Priority

 sets the VLAN user priority. Choices are 

0

 (default) to 

7

. 

Refer to 

VLAN ID and Priority

 on page 758 for more information. 

Type

 indicates the supported VLAN Ethernet type which is 

0x8100

. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands