manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 162

Test Setup - Test Configurator, Timer, and System

150

88000 Series

Clock

For E1:

TERM

 provides an input that terminates the E1 signal. 

MON

 provides high-input impedance and compensation for 

resistive loss. This setting is useful for monitoring E1 signals at 
monitor points, which are resistor-isolated. 

BRIDGE

 provides high-input impedance for bridging lines that are 

already terminated. This setting is useful for bridging directly 
across copper cable pairs. 

Line Coding

 allows the selection of the interface line coding. 

For DS1: 

AMI

 and 

B8ZS

 (default). 

For E1: 

AMI

 and 

HDB3

 (default). 

Framing

: Allows the selection of the interface framing. 

For DS1: 

SF

, 

SLC-96

, and 

ESF

 (default).

For E1: 

PCM30

 (default), 

PCM30 CRC-4

, 

PCM31

, and 

PCM31 CRC-4

.

Frequency (MHz)

 displays the frequency of the received signal rate. 

Offset (ppm)

 displays the positive or negative frequency offset 

between the standard rate specification and the rate from the received 
signal. The background color is used to indicate if the received clock 
meets (green) or not (red) the standard rate specification. 

Signal

Standard Rate specification

DS1

1544000 ± 8 bit/s (± 4.6 ppm)

E1

2048000 ± 10 bit/s (± 4.6 ppm)

2MHz

2048000 ± 10 bit/s (± 4.6 ppm)

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands