manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 123

Test Setup - Test Configurator, Timer, and System

Power Blazer

111

Modify Structure Button

Framing

 

Note:

For OTN BERT, and SONET/SDH BERT test applications for rates up to 10G, 
the framing is set to 

Framed

. 

For OTN BERT test application, parallel interfaces, allows the selection 
of the test framing type. For serial interfaces, Multi-Channel OTN, OTN 
BERT, and SONET/SDH BERT test applications, the 

Framing

 is set to 

Framed

. For OTN - SONET/SDH BERT test application, the test is 

framed. 

Framed

 (default): A single Pattern or Ethernet client applied 

toward the physical lanes. 

20 Unframed Logical Lanes

: Independent test pattern in each 

logical lane. Available with:

OTU4 (4 Lanes) [111.81 Gbit/s]

. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands