manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 618

Glossary

606

FTB-700G/800 Series

Ethernet Cables

Ethernet Cables 

Minimum Category 3 cable is required for 10Base-T connection while 
Category 5 cable is required for 100Base-TX and 1000Base-T connections.

Maximum cable length (between two nodes) for 10Base-T, 100Base-TX, or 
1000Base-T connection is 328 feet (100 meters).

Straight Through Cable (10/100 Mbit/s)

An Unshielded Twisted Pair (UTP) straight through cable is required to 
connect a 10Base-T/100Base-TX NetBlazer port to a layer 1 or 2 device 
(ex: HUB, switch).

Crossover Cable (10/100 Mbit/s)

An Unshielded Twisted Pair (UTP) crossover cable is required to 
connect the 10Base-T/100Base-TX NetBlazer port to a layer 3 device 
(ex: router).

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands