manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 552

Test Control

540

FTB-700G/800 Series

Lpbk Tool Button (Loopback Tool)

Interface Tab

Physical Interface 

Interface/Rate

 allows the selection of the loopback tool interface 

rate: 

10/100/1000M

 

Electrical

 (default), 

100M

 

Optical

, 

1GE Optical

, or 

10GE LAN

. 

10GE LAN

 is only available when the 

loopback tool runs on Port #1. 

Connector

 displays the NetBlazer’s port for the selected 

interface/rate. 

Clock Mode

: Displays the clock mode 

Internal

: Internal clock of the unit (STRATUM 3). 

RX Power (dBm)

 indicates the current received power level of the 

optical laser in dBm. 

Green: Power level in range.
Yellow: Power level out-of-range.
Red: Loss of signal or power level is close to damage.
Gray: Invalid operational range value or not supported by the 
optical transceiver. 

Power Range (dBm)

 indicates, when supported, the received 

power level range of the optical laser in dBm. 

RX Frequency (MHz/GHz) 

indicates the frequency of the input 

signal. When no frequency reading is possible, “

--

” is displayed. 

Interface/Rate

Connector

When using Port 1

When using Port 2 

10GE LAN

 

Port 1 - SFP+

1GE Optical 
100M Optical 

Port 1 - SFP

Port 2 - SFP

10/100/1000M Electrical  Port 1 - RJ45

Port 2 - RJ45

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands