manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 545

Test Control

NetBlazer

533

Headset/DTMF Button

Headset/DTMF Button 

Note:

Only available with 

ISDN PRI

 test application.

The 

Headset/DTMP

 allows to connect a B-Channel (Speech or 3.1 kHz) to 

the headset and DTMF tones can be generated using the keyboard. 

Enable/Disable Headset and DTMF 

Enable Headset and DTMF

 button is used to enable the Headset and 

DTMF on the selected channel. The button is only available when one 
or more 

Speech

 or 

3.1 kHz

 calls are active, otherwise the button is 

grayed out. 

Disable Headset and DTMF

 button indicates that the Headset and 

DTMF is enabled on the selected channel. Tapping on the 

Disable 

Headset and DTMF

 button disables the Headset and DTMF from the 

selected channel. 

Channel 

Allows to select the channel used to connect the Headset and DTMF. Only 
active 

Speech

 and 

3.1 kHz 

channels are displayed. Other channels 

including the D-Channel will not be available. 

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands