manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 466

Test Results

454

FTB-700G/800 Series

WIS

WIS 

From the

 Test

 menu, tap 

Results

, and the 

WIS

 tab. 

Traces/Label

J0 Trace

 displays the 

J0 Trace

 value in 16-bytes format. 

J1 Trace

 displays the 

J1 Trace

 value in 16-bytes format. 

Path Signal Label (C2)

 displays the content of the STS SPE including 

the status of the mapped payload. 

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands