manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 389

Test Results

NetBlazer

377

Quality Level (SyncE)

QL Mismatch Frame Count

 gives the total count of information and/or 

event frames received not matching the expected Quality Level. Only 
available when the 

QL Mismatch Monitoring

 check box is selected. 

QL-SSU-B

8

Type VI slave clock (G.812)

QL-INV9

9

Quality Level Invalid 9

QL-EEC2/ST3 
(default)

10

Ethernet Equipment Clock Option 2
Traceable to Stratum 3 (G.812 Type IV)

QL-EEC1/SEC

11

Ethernet Equipment Clock Option 1
Synchronous Equipment Clock (G.813 or G.8262, Option 1)

QL-SMC

12

Traceable to SONET Minimum Clock (G.813 or G.8262, Option 2)

QL-ST3E

13

Traceable to Stratum 3E (G.812 Type III)

QL-PROV

14

Provisionable by the Network Operator (PNO)

QL-DNU/DUS

15

Do Not Use
Do Not Use for Synchronization

Quality Level 

value

SSM

Description

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands