manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 13

NetBlazer

1

1

Introducing the Ethernet and 

Multiservice Tester 

ALL-IN-ONE Ethernet/optical solution for field technicians installing, testing 
and troubleshooting FTTx, fronthaul, backhaul, small-cell, DAS, remote 
radio head and data center networks, in addition to OTN, SONET/SDH, 
Fibre Channel, GigE and 10 GigE, CPRI/OBSAI and SyncE/1588 PTP 
services, with the added support of OTDR and iOLM capabilities. 

Features 

Technical Specifications

To obtain this product’s technical specifications, visit the EXFO Web site at 

www.exfo.com

.

Features

Model

860GL

860

860G

720G

730G

730G+

730G+

810

810G

870

880

Intelligent  Apps.

X

X

X

X

X

X

Ethernet

X

X

X

X

X

X

Packet  Sync

X

X

X

X

X

Fibre  Channel

X

X

X

X

X

Wireless

X

X

X

X

X

OTN

X

X

X

SONET/SDH

X

X

X

X

DSn/PDH

X

X

ISDN PRI and NI/CSU

X

X

OTDR and iOLM

X

X

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands