EXFO bv10 User Manual Download Page 80 | Manualshive

Page: 80 / 116

EXFO bv10 User Manual Download Page 80

Test Applications

74

BV10

Smart Loopback Test

Smart Loopback Test

The Smart Loopback feature loops back the stream of data
(frames/packets). It retransmits incoming frames/packets after exchanging
the source and destination addresses as well as ports at multiple layers
(Ethernet MAC, IP, and UDP/TCP).

Smart Loopback can be enabled (default) or disabled. Refer to

smart-loopback enable|disable

on page 70 for more information.

Modes

The Smart Loopback mode limits the address/port swapping to a specific
layer. The BV10 supports the following Smart Loopback modes:



UDP/TCP (default) – Swap MAC addresses, IP addresses, UDP or TCP
ports when present and addressed to the unit’s TEST port MAC/IP
address. In other words, swap from Layer 2 up to Layer 4 when
present.



IP – Swap MAC addresses, IP addresses when present and addressed
to the unit’s TEST port MAC/IP address. In other words, swap from
Layer 2 up to Layer 3 when present.



Ethernet – Swap MAC addresses when addressed to the unit’s TEST
port MAC address. In other words, swap Layer 2 when present.



Ethernet All Unicast – Swap MAC addresses when the address is
unicast, regardless of the unit’s MAC address.

Refer to

smart-loopback mode ethernet-all-unicast|ethernet|ip|udp-tcp

page 70 for more information.

«
...
78
79
80
81
82
...
»

Summary of Contents for bv10





















































































































Reviews:

No comments