manualshive.com logo in svg

EXFO bv10, User Manual, Page: 70 / 116

Share
Download
EXFO bv10 User Manual Download Page 70

CLI Command Reference

64

BV10

Configuration Commands

interface lan|test speed auto 

Description

Auto-negotiates all supported LAN (10/100) or Test (10/100/1000 for 

electrical or 1000 for optical) port speeds. 
This command cannot be sent through the Test port. 

Syntax

interface lan|test speed auto

Example

bv10-100>

 interface lan speed auto

interface test speed 10|100|1000 auto 

Description

Auto-negotiates the specified electrical TEST port speed (10/100/1000). 
This command cannot be sent through the Test port. 

Syntax

interface test speed 10|100|1000 auto

Example

bv10-100>

 interface test speed 100 auto

interface test speed 10|100|1000 force 

Description

Forces the electrical TEST port speed (10/100/1000) to the specified 

value; no auto-negotiation is performed. 
This command cannot be sent through the Test port. 

Syntax

interface test speed 10|100|1000 force

Example

bv10-100>

 interface test speed 1000 force

Summary of Contents for bv10





















































































































Reviews:

No comments