AL-1855-EDPB
Feature Programming
:
Turn the ignition key “on, then “off”
1.
Within 7 seconds of step 1, press the valet switch 5 times
2.
(user features) or 10 times (installer features). This
siren/horn will sound.
Press the valet switch the number of times equal to the
3.
feature number you wish to access.
Press the controller/transmitter button that corresponds to
4.
the desired setting.
To change additional features, repeat steps 3-4.
5.
To exit programming, turn the ignition key “on”, then “off”
6.
or the system will exit automatically if there is a 10 sec-
ond delay between any steps.
Tach Learning Procedure
:
Turn the ignition key “on”
1.
Within 10 seconds of step 1, press the brake pedal 5
2.
times. The siren/horn will chirp 5 times.
Start the engine with the key. When tach is successfully
3.
learned, the status light will turn on solid.
If you need to relearn a later tach signal due to cold start/
4.
high idle, you can press the valet switch once to learn
the current tach signal. The status light will turn off and
back on to indicate it has relearned.
Programming Controllers/Transmitters
:
Be sure to have all controllers/transmitters present and be
1.
sure the system is in a disarmed/unlocked state.
Turn the ignition key “on”.
2.
Within 7 seconds of step 1, press the valet switch 5 times.
3.
The siren/horn will sound.
Press LOCK on one transmitter/controller until you hear a
4.
single chirp.
Repeat step 4 for each transmitter/controller to be pro-
5.
grammed.
To exit programming, turn the ignition key “off” or the sys-
6.
tem will exit automatically if there is a 10 second delay
between any steps.
Programmable Features Matrix
DELUXE 2-WAY ALARM & REMOTE START SYSTEM
The 2-Way Controller
Part number: 157-07
Battery: Rechargeable
Frequency: 900MHz
1
2
3
1
2
4
The 1-Way Transmitter
Part number: 1410-07
Battery: 1 x CR2032
Frequency: 900MHz
LOCK button
1.
UNLOCK button
2.
TRUNK button
3.
3
4
START button
4.
PROGRAMMING button
5.
Technology
5
User Feature Programming: Ignition on, off, press valet 5 times
# Feature
Lock Button
Unlock button
Trunk button
”START” button
1 Secure Code
1, 0 (default)
2 Last Door Arming
Off
On w/o lock
On w/ Lock
3 Automatic Rearming
Off
On w/o lock
On w/ Lock
Enhanced Rearm
4 Starter Interrupt Functions
Alarm
Anti-Grind Only
Alarm+Anti-Grind
Automatic
5 Ignition Override
On
Off
6 Ignition Lock/Unlock
Off
Lock w/ IGN ON Unlock w/ IGN Off
Lock + Unlock w/
IGN On/Off
7 Open Door Bypass For Ign. Locks
On
Off
8 Confirmation Chirps
On
Except Valet
mode
On Demand
Off
9 Chirp Volume
Low
Med Low
Med Loud
Loud
10 Alarm Cycle
30 sec
60
90
120
11 Flashing Lights Confirmation
On w/
RS Steady
On w/ Disarm +
RS Flashing
Steady During RS
Flashing During
RS
12 Disarm Upon Trunk Release
On
Off
13 Arming Delay
3 sec
15
30
45
14 Alarm Functions Bypass
On
Off
15 Anti-carjack
Ignition Only
Door Only
Ig Door
Off
16 Open Door Warning Upon Arm
On
Off
17 Remote Start Activation
Start / Pulse x 2 Start / Pulse x 1 Lock+Unlock
18 Remote Start Run Time
5 min
10 min
15 min
20 min
Installer Feature Programming: Ignition on, off, press valet 10 times
1 Doorlock pulse
0.8 sec
3 sec
Double unlock
Total closure
2 Light Relay Functions
Dome light
Lock
Ignition
Acc
3 Horn Relay Functions
Horn
Unlock
Trunk Release
Pulse after Start
4 Turbo Timer
Off
1 min
2 min
3 min
5 Manual Transmission
On
Off
6 Engine detection
Tachless Hi
Tachless Lo
Tach Wire
Datatach
Crank Only (press Lock + Unlock)
7 Crank Time
0.7 sec
1 sec
1.5 sec
2.25 sec
8 Pink/White Ignition Wire Function
Ignition
Accessory
Start
9 Arm/Disarm/Additional Ch.
Arm/Disarm
Arm/Ch 5
Ch4/Disarm
Ch 4/Ch 5
10 Gas or Diesel Engine
Gas
Diesel
(15 sec. Delay)
Diesel
(20 sec. Delay)
Diesel
(30 sec. delay)
11 Remote Start Lock control
Off
Lock after start
Unlock before start
Both
12 Low Temp Crank Extender
0ms
200ms
300ms
400ms
13 Data Port Protocol
D2D (Trilogix)
ADS (iData)
14 Lock on prewarn
On
Off
15 Blue Satellite Port Blue Wire Function
Status
Pulse Before
Start
Pulse After Start
Below Freezing
Pulse After
Engine Off
16 Low Current/Motorcycle Mode
On
Off
Transmitter/Controller Operations
:
LOCK/ARM
: Press and release “lock” once
UNLOCK/DISARM
: Press and release “unlock” once
TRUNK RELEASE/2ND CH
: Press “trunk” for 3 seconds
REMOTE START
: Press “start” twice in 5 seconds
(see user feature #17 for options)
REMOTE VALET
: Press “start” within 5 seconds of pressing
“unlock”
LOW BATTERY\LOW TEMP AUTO STARTING
: Press “start”
within 5 seconds of pressing “lock”
PANIC
: Press “lock” or “unlock” for 3 seconds
SILENT ARM/DISARM
: Press “trunk” twice in 5 seconds
SENSOR BYPASS
: Press “trunk” within 5 seconds of arming
