Exabyte VXA-2 AUTOPAK1X7 Product Manual Download Page 90

Page: 90 / 104

RODUCT

ANUAL

1010964

Appendix

A—S

PECIFICATIONS

TORAGE

APACITY

The storage capacity of the Exabyte VXA-2 AutoPak

1x7

Autoloader varies with

the model of data cartridge being used and the type of data being stored. With

seven VXAtape V23 data cartridges, the autoloader has a maximum storage

capacity of approximately 1.1 terabytes (TB), assuming a 2:1 compression ratio.

IZE

AND

EIGHT

Table A-1

lists the dimensions and weight of the autoloader.

ERFORMANCE

PECIFICATIONS

This section describes the following performance specifications for the

autoloader:

Data transfer rate

Tape drive performance

Autoloader power-on self-test time

Move complete time

Robot reliability

ATA

RANSFER

ATE

The autoloader can achieve a data transfer rate of up to 43.2 gigabytes (GB) per

hour (assuming a 2:1 compression ratio).

APE

RIVE

ERFORMANCE

When installed in the autoloader, the tape drive performs within its

specifications. For information about tape drive performance specifications,

refer to the

Exabyte VXA-2 SCSI Tape Drive Product Manual

Length

46.2 cm (18.3 inches)

Width

21.1 cm (8.3 inches)

Depth

21.3 cm (8.4 inches)

Weight

9.8 kg (21.5 lbs.) with the cartridge magazine

and seven cartridges

Summary of Contents for VXA-2 AUTOPAK1X7









































































































Search results

Summary of Contents for VXA-2 AUTOPAK1X7

Reviews:

Exabyte VXA-2 AUTOPAK1X7, Product Manual, Page: 90 / 104

Search results

Summary of Contents for VXA-2 AUTOPAK1X7

Reviews: