1
Connect Devices
3
Apply Power
4
Con
fi
gure Network
2
Connect to Network
A
LED Descrip
Ɵ
ons
PROCEED TO STEP 2
PROCEED TO STEP 3
Insert the SIM card and
mount the antenna
WAN
(enabled by default)
2G/3G
(EC350 only)
Make sure that the SIM card has
a mobile data plan and allows
text messaging, and that PIN code
security has been disabled.
Apply power
Sta
Ɵ
c IP or 2G/3G:
PROCEED TO STEP 4
DHCP:
PROCEED TO SECTION B ON REVERSE
LED Name
Color
Indica
Ɵ
on
Possible ac
Ɵ
ons
Modem (EC350 only)
OFF
Modem disabled
Steady red
Modem failure
See the User Manual for more informa
Ɵ
on.
Flashing red
SIM card failure
Check that the SIM card is correctly inserted and not damaged.
Steady orange
PIN code enabled on SIM card
Disable PIN code on the SIM card.
Flashing orange
No APN server speci
fi
ed
Set the APN (Access Point Name) from the onboard webpage.
Steady green
Modem registered on mobile network
Flashing green
Modem is searching for mobile network.
RS485/RS232
OFF
Port disabled
Steady red
Port failure/communica
Ɵ
ons issue
See the User Manual for more informa
Ɵ
on.
Steady green
Communica
Ɵ
ons OK
Uplink/WAN
Steady green
Connected to Internet
Steady red
Incorrect IP se
ƫ
ngs
DHCP: Check for DHCP server on network.
Sta
Ɵ
c IP: Check se
ƫ
ngs for IP address, gateway and DNS.
Flashing red
Unable to connect to Internet
Check network se
ƫ
ngs and
fi
rewalls.
Gateway
OFF
Unit has no power, or is star
Ɵ
ng up
Steady green
Normal opera
Ɵ
on
Flashing green
Firmware update in progress.
Steady red
Hardware failure
See the User Manual for more informa
Ɵ
on.
Flashing red
Applica
Ɵ
on failure
See the User Manual for more informa
Ɵ
on.
Power
OFF
No power
Steady green
Unit has power
Ethernet Link
(located on RJ-45 ports)
OFF
No network detected
Orange
fl
icker
Ac
Ɵ
vity on 10 Mbps Ethernet network
Green
fl
icker
Ac
Ɵ
vity on 100 Mbps Ethernet network
See reverse for informa
Ɵ
on about the connec
Ɵ
ons
Insert SIM card
Connect network
to
WAN
port
Connect Serial
Devices
Make sure that there is a
good connec
Ɵ
on to the
mobile network.
See LED Descrip
Ɵ
ons.
Connect 12–48 VDC to pin +
Connect Power Ground to pin -
Ethernet with
Sta
Ɵ
c IP address
2G/3G
(EC350 only)
PROCEED TO SECTION B ON REVERSE
Con
fi
gure IP se
ƫ
ngs.
See sec
Ɵ
on C on reverse.
To check the mobile signal strength on EC350:
Press and release the Mode bu
Ʃ
on. The top 5 LEDs
will now show signal strength for 60 seconds:
•
1 Flashing Red LED: No/unknown signal
•
1 Flashing Orange LED: Poor signal
•
1 Flashing Green LED: OK signal
•
2-5 Flashing Green LEDs: Good to op
Ɵ
mum signal
RS-485 RS-232
SSIM
Connect Ethernet
Devices to LAN port
LAN
Before you install the Netbiter, make sure that you have all the necessary
informa
Ɵ
on about your local network environment. Contact your network
administrator if in doubt.
Select
Network
Type
Network
Type
