EVS Synapse U4T100 Installation & Configuration Manual Download Page 53 | Manualshive

Page: 53 / 68

background image

EVS Broadcast Equipment SA

51

Setting up card

To be able to program the card direct we need to perform two steps. One
is setting up of the IP address of the card and second will be making the
board recognized as stand alone entity.

To set-up the IP address of the card goto the system view within the
Cortex program. Select the HLDxxx and goto the device view tab. Within
the device tab you will be able to setup the IP address, netmask and
gateway.

The next step is to make the card available as a stand alone card within
the system. To add this card you need to go to the network tab at the top
of the cortex program. Then go to add network device and choose add
ACP device.

Fill out the name of the card and also the ip address.

«
...
51
52
53
54
55
...
»

Summary of Contents for Synapse U4T100





































































Reviews:

No comments

Related manuals for Synapse U4T100

Brand: iDance Pages: 25

Brand: Geberit Pages: 49

Brand: Japan' Gold Pages: 5

Brand: Abus Pages: 14

Brand: Abus Pages: 16

Brand: Y-cam Pages: 31

Brand: Abus Pages: 16

Brand: Fenton Pages: 16

Multi-room system

Brand: Systemline Pages: 22

Brand: auna multimedia Pages: 124

Brand: Care Call Pages: 2

Brand: Aiwa Pages: 20

JV-B765HV9V22DNR

Brand: JV vision Pages: 12

Brand: NAPCO Pages: 4

Brand: Turbosound Pages: 13

Brand: Hitron Pages: 21

SpreadNet SN962-PENDANT

Brand: C&K systems Pages: 2

Brand: Neilsen Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands