EVS Synapse U4T100 Installation & Configuration Manual Download Page 52 | Manualshive

Page: 52 / 68

background image

INSTALLATION AND CONFIGURATION MANUAL

U4T100-U4T140

50

Precautions

Backup your

settings

It is advised to back up the settings before upgrading the card. To do this,
select the frame and card you want to upgrade. Then choose “Card” in the
menu and select “Backup card”. An exact copy of the card’s menu can be
stored as .xml file in the following window. The next image displays the
window where this is done.

At your own risk

During the upgrade process, the card will stop functioning for a period of
time. Make sure the card you are going to upgrade is currently

not

being

used by anyone in your company.

Note

Use cortex version 1.09.01 or later. This software can
be downloaded from https://mi‐sftp.evs.com/.

«
...
50
51
52
53
54
...
»

Summary of Contents for Synapse U4T100





































































Reviews:

No comments

Related manuals for Synapse U4T100

Brand: Panasonic Pages: 73

Brand: Panasonic Pages: 12

WJND400 - NETWORK DISK RECORDER

Brand: Panasonic Pages: 21

Brand: Panasonic Pages: 2

RXD15 - RADIO CASSETTE W/CD

Brand: Panasonic Pages: 8

Brand: Nacon Pages: 12

Brand: U-Prox Pages: 3

Brand: ACTi Pages: 2

Picomig 305 D2 puls

Brand: EWM Pages: 84

Brand: Dahua Pages: 29

Brand: TRASSIR Pages: 2

Brand: Young Shin Electronics Pages: 10

Brand: BUCKINGHAM MFG Pages: 5

Brand: SAKUTUS Pages: 10

DWC-B1362TIR650

Brand: DW Pages: 20

Brand: SICK Pages: 112

Brand: Novus Pages: 56

Brand: W Audio Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands