Evolution 026-0007 Original Instructions Manual Download Page 13

13

www.evolutionpowertools.com

EN

DE

• Safely store the outer blade flange and associated fixings.
•  Rotate the lower blade guard up into the upper blade guard 

using the manual thumb lever.

 

(Fig. 5) 

•   Carefully remove the blade (if fitted) from the machine. 
•   Thoroughly clean inner and outer blade drive flanges.

Note: The inner blade flange can be left in place if desired, but it 
should be checked and thoroughly cleaned. If it is removed from 
the machine it must be replaced back in the same orientation as 
it was before removal.
 •  Thoroughly clean the blade around the bore area (both 

surfaces) where the blade flanges will touch and clamp  
the blade.  

• Install the (new) blade.
•  Ensure that the direction of rotation arrows printed on the 

blade, match the direction of rotation arrows found on the 
machines upper and lower blade guards. (Fig. 6)

• Reinstall the outer drive flange, the socket headed arbor 

screw, and its associated fixings.

Note: The outer drive flange has a specially machined bore 
which incorporates two opposed ‘flats.’ (Fig. 7) These ‘flats’ 
engage with two complimentary ‘flats’ machined into the 
machines arbor shaft.
•  Re-engage the arbor lock and tighten the arbor socket headed 

screw securely using the Hex Key.

•  Release the arbor lock button.
•  Return the Hex Key to its dedicated storage position.
•  Check that the arbor lock has fully released by manually 

rotating the blade.

•  Check the operation of the lower blade guard.

(11) 

PARALLEL EDGE GUIDE  

A Parallel Edge Guide (Fig. 8)

 

which can be particularly  

helpful when rip cutting, is supplied with all CCS machines. 
The guide can be fitted to the front of the sole plate.
The guides arm should be inserted through the rectangular slots 
positioned at either side (front) of the pressed steel sole plate, 
and slid under the centrally located adjustment locking screw. 

(Fig. 9)

 

 

Note: The Parallel Edge Guide can be fitted on either side of the 
sole plate.

WARNING:  Only fit and adjust the Guide with the machine 
disconnected from the power supply. 

Note: The arm of the Parallel Edge Guide must pass through all 
of the rectangular slots provided in the sole plate. 

Fig. 5

Fig. 6

Fig. 7

Fig. 8

Summary of Contents for 026-0007





















Reviews: