background image

E2615-H

2

S

Rev 24.08.2022

Hydrogen Sulfide

Colorless toxic, corrosive and flammable gas with a smell of rotten eggs. Occurs in natural
gas, volcanic gases, petroleum, and some sources of well water. It results from the
anaerobic decay of sulfur-containing proteins, e.g. in sewers.

Synonyms: Hydrosulfuric acid, Sewer gas, Sulfuretted hydrogen.

Chemical formula

H

2

S

Molar weight

34

Conversion

1 ppm = 1.40 mg/m

3

Relative gas density (to air)

1.17

Boiling point

−60 °C

Low explosive limit (LEL), % vol.
in air

4.0

Upper explosive limit (UEL), %
vol. in air

44.0

Odor

The characteristic smell of rotten eggs. Above 30 ppm, the odor is

described as sweet or sickeningly sweet.

Odor threshold

0.01-1.5 ppm

Note:

Sense of smell becomes rapidly fatigued and can NOT be

relied upon to warn of the continuous presence of H

2

S.

Hazards

Highly flammable, explosive gas.

Broad-spectrum poison, mostly affecting the nervous system. At

low concentrations causes eye irritation, a sore throat and cough,

nausea, shortness of breath, and pulmonary edema. Long-term,

low-level exposure results in fatigue, loss of appetite, headache,

poor memory, irritability, and dizziness. Exposure to high levels

can induce immediate collapse, with loss of breathing and a high

probability of death.

Exposure

limits

(Commission
Directive
2009/161/EU)

TWA

7 mg/mm

3

/ 5 ppm

STEL

14 mg/mm

3

/ 10 ppm

IDLH
(NIOSH)

140 mg/mm

3

/ 100 ppm

Conversion of ppm to mg/m

3

is calculated for 25°C and 1 atm.

3

Summary of Contents for E2615-H2S












Reviews: