manualshive.com logo in svg

evertz 9821EMR-AG-HUB, User Manual

Share
Download
evertz 9821EMR-AG-HUB User Manual Download Page 50

9821EMR-AG-HUB  

User Manual 

 

Page - 38

 

Revision 0.1

 

 

 

Dante module 1 will occupy slots 3 and 5, but only slot 3 shows status. 

Dante module 2 will occupy slots 4 and 6, but only slot 6 shows status. 

Dante module 3 will occupy slots 7 and 9, but only slot 7 shows status. 

Dante module 4 will occupy slots 8 and 10, but only slot 10 shows status. 

Dante module 5 will occupy slots 11 and 13, but only slot 11 shows status. 

Dante module 6 will occupy slots 12 and 14, but only slot 14 shows status. 

Dante module 7 will occupy slots 15 and 17, but only slot 15 shows status. 

Dante module 8 will occupy slots 16 and 18, but only slot 18 shows status. 

 

The active slots will show the modules’ Status, Name, Serial number Firmware version and 

Temperature, also the user can download and upload each module’s config. 

 

Network Control is not being used currently. 

 

 

Figure 

 

5-7 : WebEASY

® 

- 9821EMR-FC\Module 

 

5.6.  MODULE CONFIGURATION 

In this section the overview of the Dante module allocations are being presented. 

 

 

Figure 

 

5-8 : WebEASY

® 

- 9821EMR-FC\Module Configuration 

 

When user click on the active Dante module, the status window for that module will open and provide 

information on Module’s Name, firmware version of the 9821EMR-IO-Dante-64, Temperature, Status, 

TDM connection to and from Module and Genlock presence. 

Summary of Contents for 9821EMR-AG-HUB



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands