evertz 7707VT13-4-HS Manual Download Page 19

Page: 19 / 24

7700 MultiFrame Manual

7707VT-4-HS Quad SD/Dual HD-SDI Fiber Transmitter

Revision

1.4

Page - 15

4.2.8. Controlling Loopback Connector Output

The

VOUT

menu item allows the user to control which input video signal will be passed through to the

“HD/SDI OUT” connector on the 7707VT-4-HS. To select the output signal, select the

CTRL

menu item in

menu level 1, then use the toggle switch to display the

VOUT

option and press the pushbutton to select it.

CTRL

VOUT

ON
OFF

The possible selections are as follows:

VID1

Video input channel 1 signal will be available at the output

VID2

Video input channel 2 signal will be available at the output

VID3

Video input channel 3 signal will be available at the output

VID4

Video input channel 4 signal will be available at the output

4.2.9. Controlling the Behavior of the Laser

On the 7707VT-4-HS the

LASR

option allows the user to set the behavior of the laser transmitter when

there is no video signal applied to the video inputs. To set the laser behavior, select the

CTRL

menu item

in menu level 1, then use the toggle switch to display the

LASR

menu selection and press the pushbutton

to select it. Use the toggle switch to choose between

CONT

and

DISC

and press the pushbutton to select

the mode of operation.

CTRL

LASR

CONT
DISC

The possible selections are as follows:

CONT

Laser will transmit continuously regardless of whether there are
valid input video signals present on the inputs of the 7707VT-4-
HS.

DISC

The laser will turn off when there is no recognizable video on
the 7707VT-4-HS inputs.

Note: With the 7707VT-4-HS set to discontinuous mode, due to the laser turning
off, the companion 7707VR-4-HS will indicate an optical signal loss when no input
video signal is present at the 7707VT-4-HS.

4.2.10. Setting the Orientation of the Text on the Card Edge Display

The

DISP

display option allows the user to set a horizontal or vertical orientation for the card edge display

messages. To set the display orientation, select the

CTRL

menu item in menu level 1, then use the toggle

switch to display the

DISP

menu selection and use the pushbutton to select it. Use the toggle switch to

change between

HOR

and

VERT

. Press the pushbutton to make your selection.

CTRL

DISP

HOR
VERT

The possible selections are as follows:

HOR

Horizontal display used when the module is housed in the 1
rack unit 7701FR frame or the stand-alone enclosure.

VERT

Vertical display used when the module is housed in the 3-rack
unit 7700FR frame.

Summary of Contents for 7707VT13-4-HS

























Search results

Summary of Contents for 7707VT13-4-HS

Reviews:

Related manuals for 7707VT13-4-HS

Brands by name

Popular brands

evertz 7707VT13-4-HS, Manual

Search results

Summary of Contents for 7707VT13-4-HS

Reviews:

Related manuals for 7707VT13-4-HS

Brands by name

Popular brands