evertz 7707VT13-4-HS Manual Download Page 16

Page: 16 / 24

7700 MultiFrame Manual

7707VT-4-HS Quad SD/Dual HD-SDI Fiber Transmitter

Page -

Revision

1.4

4.2.1. Display of Warning Status Indications

The top level, default display indicates overall card status and warnings:

Card is functioning properly

LASR…ERR

Laser Error Warning – Flashing indication alternates between

LASR

and

ERR

Pressing the pushbutton from this default display will allow the user to select from

STAT

(status) and

CTRL

(control) menu items.

4.2.2. Displaying the Video Standard

The 7707VT-4-HS detects the video standard of the signals present at its inputs. To display the video
standard, select the

STAT

menu item in menu level 1, then use the toggle switch to display the desired

video channel (from

VID1

VID4

) and press the pushbutton to select it. Use the toggle switch to

display the

STD

option and use the pushbutton to select it. For the sake of brevity, only the description for

Video Input 1 (VID1) will be provided. The video standard will be displayed from the list below:

1080i/60

1080i/59.94

1080i/50
1035i/60

1035i/59.94

1080i/48

1080i/47.96

720p/60

720p/59.94

N270

P270

SDTI-N270
SDTI-P270

LOS

(Loss of Signal)

STAT

VID1

STD

Standard
LOS

Standard:

One of the above mentioned video standards will be listed.

LOS

Loss of Signal – A valid output is not present.

4.2.3. Displaying the Equalization Strength

The 7707VT-4-HS performs automatic cable equalization to compensate for up to 100m of Belden 1694
(or equivalent) cable at 1.485Gb/s or 250m at 270Mb/s. To display the applied equalization, select the

STAT

menu item in menu level 1, then use the toggle switch to display the desired video channel (from

VID1

VID4

) and press the pushbutton to select it. Use the toggle switch to display the

option and

use the pushbutton to select it. For the sake of brevity, only the description for Video Input 1 (VID1) will be
provided.

STAT

VID1

0% to 100%

Applied equalization is indicated as follows:

0% to 100%

Indicates applied equalization in percentage of maximum
available equalization strength. A very weak or
disconnected input signal will indicate

100%

equalization.

Summary of Contents for 7707VT13-4-HS

























Search results

Summary of Contents for 7707VT13-4-HS

Reviews:

Related manuals for 7707VT13-4-HS

Brands by name

Popular brands

evertz 7707VT13-4-HS, Manual

Search results

Summary of Contents for 7707VT13-4-HS

Reviews:

Related manuals for 7707VT13-4-HS

Brands by name

Popular brands