evertz 7707VB-8-ASI-OC3 Manual Download

Page: 17 / 32

7700 MultiFrame Manual

7707VB-8-ASI-OC3 8 Channel ASI + Ethernet SONET / SDH Fiber Transceiver

Revision

1.0

Page - 13

The following menu is available to display performance counts:

STAT

FIBR

CIC

15m
24h

ESL
SESL
ESS
SESS
ESP
SESP
SEFS

ESL

Errored Seconds Line – Seconds having detected B2
errors.

SESL

Severe Errored Seconds Line (threshold set by
CTRL/NET/SETH/SESL).

ESS

Errored Seconds Section – Seconds having detected B1
errors.

SESS

Severe Errored Seconds Section (threshold set by
CTRL/NET/SETH/SESS).

ESP

Errored Seconds Path – Seconds having detected B3
errors.

SESP

Severe Errored Seconds Path (threshold set by
CTRL/NET/SETH/SESP).

SEFS

Severe Errored Frame Seconds – Seconds having severe
errored frames.

4.2.1.4.

Displaying the Last Interval Counter

This menu displays

Last Interval Performance Counts

recorded each time the

Live Interval

counters

expire. To display these performance counts from the

STAT

menu, use the toggle switch/pushbutton to

select the

FIBR

menu item and then choose the

LAST

menu item. The module records

Last

interval

counts for 15 minute and 24 hour intervals. The corresponding status is displayed by selecting either the

15m

24h

menu item. The following selections are available to display performance counts:

STAT

FIBR

LAST

15m
24h

ESL
SESL
ESS
SESS
ESP
SESP
SEFS

ESL

Errored Seconds Line – Seconds having detected B2
errors.

SESL

Severe Errored Seconds Line (threshold set by
CTRL/NET/SETH/SESL).

ESS

Errored Seconds Section – Seconds having detected B1
errors.

SESS

Severe Errored Seconds Section (threshold set by
CTRL/NET/SETH/SESS).

ESP

Errored Seconds Path – Seconds having detected B3
errors.

SESP

Severe Errored Seconds Path (threshold set by
CTRL/NET/SETH/SESP).

SEFS

Severe Errored Frame Seconds – Seconds having severe
errored frames.

Summary of Contents for 7707VB-8-ASI-OC3

































Search results

Summary of Contents for 7707VB-8-ASI-OC3

Reviews:

Related manuals for 7707VB-8-ASI-OC3

Brands by name

Popular brands

evertz 7707VB-8-ASI-OC3, Manual

Search results

Summary of Contents for 7707VB-8-ASI-OC3

Reviews:

Related manuals for 7707VB-8-ASI-OC3

Brands by name

Popular brands