evertz 7700 Series Manual Download Page 85 | Manualshive

Page: 85 / 94

background image

7700 MultiFrame Manual

7736CEM Composite Encoder with Monitoring

Revision 1.5

Page - 75

*Grey background indicates un-implemented or un-tested features

8.8.13. PESA 625

This parameter sets the VBI line number that contains the PESA SID information when operating in PAL-
B video mode. If the wrong line number is set, no SID will be decoded.

8.8.14. Default SID Mode

This parameter determines if the Default SID message will be displayed in the SID window when there is
no incoming source ID on the VITC.

Set to

Disable

to blank the SID window when there is no incoming source ID.

Set to

Enable

to show the Default SID message in the SID window when there is no incoming source ID.

The SID window must also be turned On

to display the default SID message.

8.8.15. Default SID Message

This parameter sets the message that will be displayed in the SID window when there is no incoming
source ID on the VITC. The text of the message can be changed.

8.9.

FAULT WINDOWS

Figure 8-11: Fault Windows Tab

«
...
83
84
85
86
87
...
»

Summary of Contents for 7700 Series































































































Reviews:

No comments

Related manuals for 7700 Series

Brand: Fenton Pages: 16

Brand: DAPAudio Pages: 18

Brand: Richie Kotzen Pages: 12

Brand: Monacor Pages: 34

Brand: Jolida Pages: 17

Brand: ZENEC Pages: 30

Brand: Rocktron Pages: 79

Brand: Rega Pages: 12

Brand: R&H Pages: 12

TUBE SCREAMER AMPLIFIER

Brand: Ibanez Pages: 52

909 Stereo Power Amplifier

Brand: QUAD Pages: 14

Brand: Laney Pages: 16

Pocketalker 2.0 PKT 2.0

Brand: William Sound Pages: 20

Brand: Texas Instruments Pages: 35

Brand: Gehrke Pages: 9

Son of Ampzilla II

Brand: SST Pages: 14

Brand: Fenton Pages: 28

High-Q Kit K1803

Brand: Velleman Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands