evertz 5782ENC-H264HD-IPASI User Manual Download

Page: 57 / 62

5782ENC-H264HD-IPASI

Professional Contribution H.264 and MPEG-2 Encoder

Revision 1.0

Page - 47

6.2.

FIRMWARE UPGRADE

There two recommended ways to upgrade the firmware for the 5782ENC-H264HD-IPASI:

1. Using the 570FC and the WebEASY

browser interface.

2. Using the 570FC and VistaLINK

Version Information interface.

Using the WebEASY

on a web interface is the fasted and recommended procedure to load the

firmware onto the 5782ENC-H264HD-IPASI.

6.3.

FIRMWARE UPGRADE USING WEBEASY

When first visiting the 5782ENC-H264HD-IPASI web interface, the user will be asked to enter a Login
and Password. Enter “

customer

” for Login and “

customer

” for Password.

On the top of the web page for the 5782ENC-H264HD-IPASI, there is a tab labeled

Upgrade

. The

Upgrade

tab is used to check current firmware version and upload the latest firmware.

Figure 6-3: WebEASY

- Upgrade Button on Top Menu Bar

Selecting the

Upgrade

tab, will take you to

Figure 6-4

where the current firmware version is shown.

Should the firmware version be outdated, you will need to download the firmware image file.



NOTE: Contact Evertz get the latest firmware file.

Summary of Contents for 5782ENC-H264HD-IPASI































































Search results

Summary of Contents for 5782ENC-H264HD-IPASI

Reviews:

Related manuals for 5782ENC-H264HD-IPASI

Brands by name

Popular brands

evertz 5782ENC-H264HD-IPASI, User Manual

Search results

Summary of Contents for 5782ENC-H264HD-IPASI

Reviews:

Related manuals for 5782ENC-H264HD-IPASI

Brands by name

Popular brands