evertz 5782DEC User Manual Download | Manualshive

Page: 28 / 60

background image

5782DEC

Professional H.264 and MPEG-2 Decoder

Page - 18

Revision 1.0

VLPRO INTERFACE

4.5.

DECODER AUDIO MONITOR

Figure 4-6: VistaLINK

®

– Decoder Audio Monitor Tab

The 5782DEC can decode up to 8 audio PIDs, and for each of the audio PIDs the following information
is monitored and displayed.

Audio PID Number:

This parameter displays the Audio Packet ID (PID) number for the audio stream

that is being decoded.

Audio Bitrate:

This parameter displays the audio bitrate for the audio stream that is being decoded.

Audio Type:

This parameter displays the audio compression type of the audio stream that is being

decoded.

Sampling Rate:

This parameter displays information such as sampling frequency; channel

configuration etc. for the audio stream that is being decoded.

Number of Channels:

This parameter displays the number of audio channels that are being decoded

by the decoder.

«
...
26
27
28
29
30
...
»

Summary of Contents for 5782DEC





























































Reviews:

No comments

Related manuals for 5782DEC

Brand: SAJ Pages: 59

Brand: Vertiv Pages: 40

Brand: Planet Pages: 20

Brand: Kramer Pages: 2

Q.HOME+ ESS HYB-G2

Brand: Q CELLS Pages: 60

Brand: Peak Pages: 28

Brand: Perle Pages: 23

Brand: ADF Web Pages: 24

SM-Universal Encoder Plus

Brand: Control Techniques Pages: 112

Brand: Kiloview Pages: 50

Brand: Kaco Pages: 42

Brand: Hall Research Technologies Pages: 12

Brand: Crystal Vision Pages: 19

Brand: Teryair Pages: 5

Brand: i3 International Pages: 2

dialog semiconductor DA913 30 Series

Brand: Renesas Pages: 2

Brand: DeWalt Pages: 56

Brand: Modernum Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands