evertz 570NAT-HW-X19 User Manual Download

Page: 26 / 56

570NAT-HW-X19

High Density Network Address Translator

Page - 16

Revision

1.0

4.1.5. Global Traffic Monitoring

Total WAN Ports Rx Bandwidth (Mbps):

This parameter displays the total received bandwidth for all

WAN Ethernet ports.

Total WAN Ports Tx Bandwidth (Mbps):

This parameter displays the total sent bandwidth for WAN

Ethernet ports.

Total LAN Ports Rx Bandwidth (Mbps):

This parameter displays the total received bandwidth for all

LAN Ethernet ports.

Total LAN Ports Tx Bandwidth (Mbps):

This parameter displays the total sent bandwidth for LAN

Ethernet ports.

4.1.6. Temperature Monitoring

FPGA Temperature:

This monitor will display the temperature of the FPGA.

4.1.7. TTL

TTL:

This field allows the user to enter the Time To Live (TTL) to be used on each separate core of the

NAT.

4.1.8. Global Data Port SFP Alarm Threshold

Use sliders to set alarm thresholds for Rx, Tx, Voltage and Temperature conditions of SFPs.

It is recommended users consult with the documentation for their SFPs and use their operational

specifications as a guideline for setting the SFP alarms.

SFP Rx Power High Alarm Threshold (dBm):

Alarm will trigger if SFP Rx exceeds this threshold.

SFP Tx Power Low Alarm Threshold (dBm):

Alarm will trigger if SFP Rx falls below this threshold.

SFP Rx Power High Alarm Threshold (dBm):

Alarm will trigger if SFP Tx exceeds this threshold.

SFP Tx Power Low Alarm Threshold (dBm):

Alarm will trigger if SFP Tx falls below this threshold.

SFP Voltage High Alarm Threshold (V):

Alarm will trigger if SFP voltage exceeds this threshold.

SFP Voltage Low Alarm Threshold (V):

Alarm will trigger if SFP voltage falls below this threshold.

SFP Temperature High Alarm Threshold (

C):

Alarm will trigger if SFP temperature exceeds this

threshold.

4.1.9. System
System Reboot:

This button allows the user to reboot the 570NAT-HW-X19 module, doing this will result

in the connection being lost temporarily while the unit resets. A warning pop-up may appear in

WebEASY

during this time, wait for the unit to reset.

Factory Reset:

This button will reset the 570NAT-HW-X19 unit to factory default settings and firmware.

Summary of Contents for 570NAT-HW-X19

























































Search results

Summary of Contents for 570NAT-HW-X19

Reviews:

Related manuals for 570NAT-HW-X19

Brands by name

Popular brands

evertz 570NAT-HW-X19, User Manual

Search results

Summary of Contents for 570NAT-HW-X19

Reviews:

Related manuals for 570NAT-HW-X19

Brands by name

Popular brands