evertz 570NAT-HW-X19 User Manual Download | Manualshive

Page: 21 / 56

background image

570NAT-HW-X19

High Density Network Address Translator

Revision 1.0

Page - 11

4.

WEB INTERFACE

The 570NAT-HW-X19 provides a built-in web interface, WebEASY

®

, which allows a user to interact with

using a standard Internet web browser. The 570NAT-HW-X19 web interface can be accessed by entering

the IP address of the control port of the 570NAT-HW-X19 into the address bar of an Internet web browser.

Refer to section

Error! Reference source not found.

for setting the network configurations.

When first visiting the 570NAT-HW-X19 web interface, the user will be asked to enter a Login and

Password. Enter “

root

” for Password and “

evertz

” for Login to get administrator privileges. When viewing

only the configurations, “

customer

” for both Login and Password.

Figure 4-1: WebEASY

®

- Login Screen

«
...
19
20
21
22
23
...
»

Summary of Contents for 570NAT-HW-X19

























































Reviews:

No comments

Related manuals for 570NAT-HW-X19

Brand: Medeli Pages: 32

Brand: Korg Pages: 90

Brand: Philips Pages: 43

Brand: Moog Pages: 4

Brand: schwa-medico Pages: 28

Brand: Gazelle Pages: 10

Brand: Roland Pages: 134

Brand: Dean Pages: 32

Brand: Vasco Electronics Pages: 20

PortaTone PSR-640

Brand: Yamaha Pages: 188

Brand: Sami Pages: 4

PortaSound PSS-595

Brand: Yamaha Pages: 10

Brand: BH Pages: 48

STUDIO COMPUTER

Brand: Spinning Pages: 24

FITNESS PARTNER

Brand: CARE FITNESS Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands