evertz 570J2K-HW-X19 User Manual Download | Manualshive

Page: 41 / 60

background image

570J2K-HW-X19

Multi channel J2K Encoder-Decoder

Revision 1.0

Page - 31

Tx Oversized Frame Count

: This parameter displays the received Tx oversized frames on this

Ethernet ports.

Clear Status:

This button allows the user to reset the Ethernet monitor statistics.

Figure

6-5 : WebEASY

®

- System Tab (Part 3)

6.1.5. Temperature Monitor:

Temperature:

This field monitors the current temperature of module.

6.1.6. Card Control

Load Factory Config:

This control is used to load factory configuration settings on the unit.

Reboot Card:

This control allows the user to perform a soft reboot on the decoder.

«
...
39
40
41
42
43
...
»

Summary of Contents for 570J2K-HW-X19





























































Reviews:

No comments

Related manuals for 570J2K-HW-X19

Brand: G-Lab Pages: 16

Brand: Z3 Technology Pages: 18

Brand: Z3 Technology Pages: 23

ACS 600 MultiDrive

Brand: ABB Pages: 94

Brand: Milexia Pages: 17

EQUINOX EQX2 4002-HT

Brand: Salicru Pages: 108

Brand: Qoltec Pages: 12

Brand: DX Engineering Pages: 4

Brand: SKP Pro Audio Pages: 20

Brand: iBasso Audio Pages: 64

Brand: MRC Pages: 6

Brand: TV One Pages: 116

Brand: MEDIAZONE Pages: 20

Brand: Siko Pages: 36

Stabiliti Series

Brand: Ideal Power Pages: 28

MIL-C2414 Series

Brand: MiLAN Pages: 4

Brand: P1PE Pages: 28

Brand: Eltako Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands