evertz 570J2K-HW-X19 User Manual Download

Page: 40 / 60

570J2K-HW-X19

Multi channel J2K Encoder-Decoder

Page - 30

Revision 1.0

Netmask:

This parameter allows the user to set the Netmask for data port.

Gateway:

This parameter allows the user to set the Gateway for data port.

Mac Address:

This parameter reflects the MAC Address of the data port.

Figure

6-4 : WebEASY

- System Tab (Part 2)

6.1.4. Data Port Monitor

Port Link Status:

This parameter returns the link status for Data port.

Received Data Ethernet Total Bitrate:

This parameter displays the Total bitrate received on this Data

port in kbps.

Transmitted Data Ethernet Total Bitrate:

This parameter displays the Total bitrate transmitted on this

output Data port in kbps.

Rx Frame Count:

This parameter displays the received Rx frames on this Ethernet port.

Rx CRC Error Frame Count:

This parameter displays the received Rx frames with CRC errors on this

Ethernet port.

Rx Undersized Frame Count:

This parameter displays the received Rx undersized frames on this

Ethernet port.

Rx Oversized Frame Count:

This parameter displays the received Rx oversized frames on this

Ethernet port.

Tx Frame Count:

This parameter displays the received Tx frames on this Ethernet port.

Summary of Contents for 570J2K-HW-X19





























































Search results

Summary of Contents for 570J2K-HW-X19

Reviews:

Related manuals for 570J2K-HW-X19

Brands by name

Popular brands

evertz 570J2K-HW-X19, User Manual

Search results

Summary of Contents for 570J2K-HW-X19

Reviews:

Related manuals for 570J2K-HW-X19

Brands by name

Popular brands