evertz 570J2K-HW-X19 User Manual Download | Manualshive

Page: 37 / 60

background image

570J2K-HW-X19

Multi channel J2K Encoder-Decoder

Revision 1.0

Page - 27

6.

570J2K-HW-X19 APP B “DECODER” WEB INTERFACE

The 570J2K-HW-X19 series of products are controlled using Web Interface. WebEasy operates using
Ethernet and SNMP control protocols.

Login

After the card has been installed and configured with the required network addresses for the control
port, it can be completely configured using the web interface. For doing this, simply type the IP address
of the control port of the 570J2K-HW-X19 module in the web browser.

Note:

Computer must be on the same Subnet in order to have communication with the module.

Figure

6-1 : WebEASY

®

- Login Menu

Login and password is “root” and “evertz” respectively.

On the web interface there are different types of menus as is shown in Figure

«
...
35
36
37
38
39
...
»

Summary of Contents for 570J2K-HW-X19





























































Reviews:

No comments

Related manuals for 570J2K-HW-X19

Brand: Samson Pages: 40

Brand: Patton electronics Pages: 16

Brand: Danfoss Pages: 36

Brand: Bang & Olufsen Pages: 44

IMP-C1000-SFP-bt-24 Series

Brand: ANTAIRA Pages: 2

Brand: Net Optics Pages: 15

Brand: Cable-Tronix Pages: 4

iSignager iS-1620

Brand: QNAP Pages: 9

Brand: Agilent Technologies Pages: 70

Brand: Sarowin Pages: 6

Brand: Esu Pages: 8

ProView PVR-8140

Brand: Harmonic Pages: 2

Brand: Ensemble Designs Pages: 27

Brand: Hall Research Technologies Pages: 5

YUAN SC710N4 HDMI2.0

Brand: JMC Pages: 8

Brand: Kramer Pages: 16

Brand: Vanner Pages: 16

Brand: Wacker Neuson Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands