background image

 

41

 

 
 

The solar system can operate at extremely high temperatures. Please do not attempt 

to decommission the system yourself, as there is a risk of serious injury.

 

 

There is also a risk of electrocution from 240VaC electricity.

 

 

1. Always wear appropriate Personal 

Protective Equipment such as gloves 
and eye protection. 

2. Even if the pipework near the cylinder 

seems cool, the panels can be at high 
temperature. Decommissioning should 
therefore only be attempted when there 
is no solar input, or the panels should 
be covered with light proof covers and 
left for at least 5 hours. 

 

 

3. Turn off the switched fused spur and 

remove the fuse. Leave the fuse holder 
open and use a padlock or similar to 
lock it open. Leave a conspicuous sign 
stating the power should not be recon- 
nected. 

4. Connect a short length of hose to the 

drain point situated at the lowest point 
of the system and place in a suitably 
sized container 

– do not drain into the 

public sewerage system. Antifreeze 
liquid must be disposed of correctly. 

5. Open the check valve. 
6. Slowly open the drain tap. When the 

initial low created by pressure has 
stopped, open the air-vent at the top of 
the solar panels. 

7. When  the  luid  has  inished  draining, 

disconnect the pipework starting at the 
upper part of the system. Caution 

– 

there may still be luid in the pipework. 

8. Dispose of any materials correctly. 
9. Panels should only be removed by 

qualiied  professionals  using appropri- 
ate access and safety equipment. 

 

The law requires employers to appoint one or more competent persons to assist them in identifying and implementing 
the preventive and protective measures required. 

 

Maintenance schedule

 

TO BE SIGNED ON Completion OF Commissioning

 

 

Date of site visits for bacterial, water 

………………………………………………………………

 

Quality and access risk assessments. 

 

Commissioned by. 

………………………………………………………………

 

Competent persons scheme unique 
identification  number. 

………………………………………………………………

 

On behalf of. 

………………………………………………………………

 

Date system commissioned and 
Handed over. 

………………………………………………………………

 

Signature of commissioning engineer. 

………………………………………………………………

 

Signature of user to confirm 
receipt and understanding 
(optional). 

………………………………………………………………

 

 

Maintenance log

 

 

Date: 

Name of engineer/company: 

Date: 

Name of engineer/company: 

Date: 

Name of engineer/company: 

 

Summary of Contents for 1000/BL1















































Reviews: