manualshive.com logo in svg

EverFocus EPOE24, User Manual

Share
Download
EverFocus EPOE24 User Manual Download Page 41

                                               

ES2446-51

 

36 

 

5.

 

Specification 

Model Name 

ES2446-51 

Standards 

Ethernet: IEEE 802.3 10BaseT, IEEE 802.3u 
100BaseTX, IEEE 802.ab 1000BaseT, IEEE 802.3z 
1000BaseSX/LX 
IEEE 802.3x Full-duplex and Flow Control 
IEEE 802.1Q VLAN 
IEEE 802.3ad Link Aggregation Control Protocol 
IEEE 802.1D Spanning Tree Protocol 
IEEE 802.1w Rapid Spanning Tree Protocol 
IEEE 802.1p Class of Service 
IEEE 802.1X Port-based Network Access Control 
IEEE 802.3at Power Over Ethernet (PoE+) 

Features 

Number of Ports: 24 
10/100/1000M RJ-45 Ports: 24 ports with IEEE 
802.3at PoE+ 
Gigabit SFP: 4, Combo with 4 10/100/1000M RJ-45 
MAC Address: 8K 
Buffer Memory: 500 Kb 
Switching Capacity: 48Gbps 
Jumbo Frames: 12.2 KB 
Transmission Method: Store and Forward 

Smart Features 

VLAN: 16, VLAN ID: 1~ 4094 
Rapid Spanning Tree Protocol 
IGMP Snooping V1&V2 
LACP/Trunk: up to 8 groups 
Quality of Service: up to 4 queues, 802.1p 
PoE Control: PoE Port Enabled/Disable, Status 
IEEE 802.1X, Source IP Filter 
Storm Control: Broadcast, Multicast, Flood Unicast 
Port: Port State, Speed/Duplex, Flow Control 
Rate Limiting, Port Mirroring 
Management: Web GUI, SNMP, Password protection 
Configuration upload/download, Firmware upgrade 

Chapter 

5 

Summary of Contents for EPOE24












































Reviews:

No comments

Brands by name

Popular brands

Load more brands