manualshive.com logo in svg

Eusso 2 & 4 Port VoIP Gateway, User Manual, Page: 95 / 112

Share
Download
Eusso 2 & 4 Port VoIP Gateway User Manual Download Page 95

ITG User’s Guide 

set gateway 

ip_addr

 

Use the 

set gateway

 command to assign a default gateway (router) for the ITG. The default 

gateway routes packet data outside or your IP subnet. 

Syntax description 

ip_addr 

The IP address of the default gateway. IP address of 0.0.0.0 stands for no 
default gateway. 

Note 

The new setting will not take effect until the ITG is reset. 

 

set mask 

ip_mask

 

Use the 

set mask

 command to set the IP subnet mask for the ITG. 

Syntax description 

ip_mask 

The subnet mask of your network. 

Note 

The new setting will not take effect until the ITG is reset. 

 

start 

Use the 

start

 command to start downloading code from TFTP server. The ITG will prompt 

you for the IP address of the TFTP server and the file to download. 

Syntax description 

This command has no arguments or keywords 

Command Line Interface

 

83

Summary of Contents for 2 & 4 Port VoIP Gateway

















































































































Reviews:

No comments