manualshive.com logo in svg

Eusso 2 & 4 Port VoIP Gateway, User Manual, Page: 32 / 112

Share
Download
Eusso 2 & 4 Port VoIP Gateway User Manual Download Page 32

 

ITG User’s Guide 

 

 

System Config. Settings Function Briefings  

1.IP Settings, which allows one to set the gateway's IP address, its subnet mask, and its Default 

Gateway IP address.  

2.H.323 Parameter Settings, which allows one to set the H.323 parameters, such as Fast Start 

Mode, Gatekeeper Mode, etc.  

3.Port Parameter Settings, which allows one to set parameters associated with each port, such as 

transmission/receive gains, comfort noise level, etc.  

4.Voice Coder Selection, which allows one to set the desired coder type, such as G.711, G.723 

or G.729A, in a per line module base. 

 

Please select Main Menu\Configure System Settings\ITG IP Settings 

 

 

 

This screen can setup your ITG IP Address, Subnet Mask and Default IP Gateway Address. 
These values will be valid after ITG reboot. 
 

Please select Main Menu\Configure System Settings\H.323 Parameter Settings 

There are H.323 General Parameter Settings, H.323 GateKeeper Settings, H.323 Aliases 
Settings. 

 

 

Configuring ITG from a Web Browser

 

20

Summary of Contents for 2 & 4 Port VoIP Gateway

















































































































Reviews:

No comments