Eusso 2 & 4 Port VoIP Gateway Page 3 User Manual Download | Manualshive

Page: 3 / 112

background image

ITG User’s Guide

How to Use This Manual

This manual was designed for the technical and non-technical users of the Internet telephony
gateway (ITG). It contains information about the functions of the ITG and instructions for
its installation, basic configuration and operation in Part I, and Part II introduces more
advanced command line interface, firmware upgrade and appendix information. Read this
section carefully for important information about the manual’s organization.

Part I

Chapter 1: Overview

This chapter provides conceptual overview and description of the ITG, explanation of how
the ITG interacts with each for enabling VoIP services, and an overview of the required tasks

Chapter 2: Installing the ITG

This chapter describes required steps to properly and safely install and configure the ITG on
your network

Chapter 3: ITG Concepts

This chapter gives information about the ITG technology and describes basic concepts using
ITG for providing telephony services over IP network

Chapter 4: Configuring ITG from Web Browser

This chapter explains procedures for configuring the ITG from a web browser

Chapter 5: Making a Call with ITG

This chapter explains how to make Internet calls from telephony devices connected to the
ITG directly or indirectly.

Chapter 6: Application Samples

This chapter provides some application examples and information on how to configure the
ITG under these samples.

Chapter 7: Troubleshooting Tips

This chapter provides troubleshooting information in case the user has problems installing or
maintaining the ITG.

Part II

Chapter 8: Command Line Interface

This chapter describes how to access the command line interface. It also contains
information about the commands used to configure the ITG.

Chapter 9: Upgrading the ITG

This chapter explains how to download new revision software and upgrade the ITG.

Preface

iii

«
1
2
3
4
5
...
»

Summary of Contents for 2 & 4 Port VoIP Gateway

















































































































Reviews:

No comments

Related manuals for 2 & 4 Port VoIP Gateway

Brand: ECKELMANN Pages: 34

Brand: 3onedata Pages: 4

ePAQ-942 Series

Brand: QEI Pages: 42

P-661H-D Series

Brand: ZyXEL Communications Pages: 113

Brand: Delta Pages: 2

Brand: AVIRE Pages: 41

NetVanta 6330 Series

Brand: ADTRAN Pages: 4

SureCross DX80G9M6S0P0V4V4C

Brand: Banner Pages: 8

VoiceFinder AP200

Brand: AddPac Pages: 46

Brand: MSA Pages: 34

Brand: Burkert Pages: 13

Brand: ClimaCheck Pages: 41

Brand: Schwaiger Pages: 24

Brand: TASHI Pages: 2

Brand: gefran Pages: 2

Brand: ADT Security Service Pages: 12

Micro Commander GC0101

Brand: Polygon Technologies Pages: 36

Brand: 3Com Pages: 488

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands