100/180 MM GRAPHICS RECORDER: USER GUIDE
User Guide
Page 141
HA261742
Issue 16 Nov 04
%
%
Minutes
s
= Disabled
0
0
Instrument Name
Instrument
Normal Display
100
Saver Display
5 0
Save After
1
Modbus Address
1
Modbus Security Disabled
Comms Channel Timeout
0
Preset Hour
1 2
Preset Minute
0
Disable Warning Dialogs
Apply
Discard
Select Home
display mode for
instrument or for
selected group
= Enabled
Home Time-out
Home Group
Dark Trend Background
Dark History Background
Scope
Group
Display Enable
Home Page
Vertical Trend
Horizontal Trend
Vertical Bargraph
Horizontal Bargraph
Numeric Page
User Screen 1
User Screen 2
User Screen 3
User Screen 4
1) Group 1
Apply
Discard
0
Group
1) Group 1
Circular Trend
Select group for
Home display
Select group for
display mode enable
These fields appear
only if Scope = 'Group'
Select Instrument or Group
Minutes
Circular Trend
Circular Trend replaces
Vertical Bargraph if 'Circular
Trend' option is fitted.
User Screen 23
User Screen 24
Remote View User Screens
User Screens 1 to 6 appear only if the
User Screens 'Lite' option is fitted.
Remaining user screen fields appear
only if the User Screens 'Full' option is
fitted. See section 2 of the options
manual for User Screen details.
100
Instrument (Section 4.3.1)
Channels (Section 4.3.3) (also Comms manual)
Apply
Discard
Job Number
1
Category
No Action
Select job number
Select: Job category
Value
5.0002
Input Type
Thermocouple
Select Linearisation
type (e.g.Type K)
Lin Type
Type K
Off, T/C, mV,V, mA,
RTD, Ohms, Digital,
Comms or Test
Range Low
0
C
Range High
1
C
Range Units
C
Scaled
Scale Low
0
V
Scale High
1
V
Select: Celsius, Fahrenheit,
Kelvins or Rankine
Units
V
Offset
0
V
Filter
None
Select: None, 2, 4, 8, 16, 32,
64, 128 or 256 seconds
Break Response
None
Select Alarm number
Cold Junction Type
Off
Descriptor
TurbineTempA
Spanned A
Span Low A
0
V
Span High A
1
V
Zone Low A
0
%
Zone High A
100
%
Max Decimal Digits
4
Colour
Alarm Number
1
Enable
Unlatched
Select Off, Unlatched, Latched or Trigger
26
Select: None, High or Low
Channel Number
1) TurbineTempA
Select channel number
18/04/01 15:17:10
Type
Absolute Low
Select Absolute,
Deviation or Rate-of-change
Threshold
Hysteresis
Dwell
0
V
0
V
0
s
These fields vary according to
Alarm Type selection
Scale Type
Scale Divisions - Major
10
1
Scale Divisions - Minor
Linear
Select None, linear or
(if option fitted), Log
These fields vary according to
Scale Type selection
PV Format
Numeric
Select Numeric or Scientific
A/B Switching
Spanned B
Zone Low B
0
%
Zone High B
100
%
Select: Off, Internal, External or Remote
Groups (Section 4.3.2)
Figure B10b
Archive
System
Save/Restore Config Security
Network
Fig B10e
See figures B10h/i/j
for option menus
Instrument
Groups
Channels
Archive
Events
Messages
Views
User Linearisations
Apply
Discard
Alarm Message
Recording Speed
Recording Interval
Archive to Media Enable
Archive via FTP Enable
Trend History Duration
Recording Enable
Ack Message
TurbineTempA
TurbineTempB
= Enabled
Etc.
1
1,200
mm/hr
s
List of all available points
(input channels, maths chan-
nels, totalisers etc.).
25.96
Days
Appear only if
'Recording Enable'
is enabled.
Trend Units
Descriptor
Trend Speed
Trend Interval
Group Number
Trend Type
Select
mm/hr or in/hr
mm/hr
1
1,200
mm/hr
s
Group 1
1) Group 1
Select Group
Adaptive
Select None, Linear, Log
or 'From Point'
Circular Speed
1 week
Circular Chart Full
New Chart
Start At
Monday
Appear only if Circular Trend
option fitted and 'Circular
Settings' enabled.
Circular Settings
Grid Type
From Point
from
Channel 3
A/B Switching
See figure B10d
Event Buttons
Views
Section 4.3.4
These fields vary according to
Input Type selection
Fig
B10f
Fig
B10g
B10 MENU STRUCTURE (Cont.)
Figure B10c Menu structure sheet 3 (Config Menus 1)
