Eurotech ZEUS Technical Manual Download Page 121

Page: 121 / 136

ZEUS Technical Manual

Appendix F - ZEUS Modem details

121

The following table shows the functions of control/status pins on the host interface:

EXP1_GPIO Signal name

Dir

Active

Function

PTT

Output

High

Push To Talk. See note 1

GSM_ON

Input

See note 2 Modem enable

GSM_STS

Output

High

Modem ON/OFF status

GPS_ON

Input

High

GPS module enable

GPS_PSUON

Input

High

Not Used (PU keeps it at logic ‘1’)

12 GPS_BOOT

Input

Not

Used

(PU keeps it at logic ‘1’)

GPS_PPS

Output

GPS Pulse Per Second

Note 1: Only available with iDEN modules.
Note 2: Please see the datasheet of the particular module used.

GSM_ON is inverted when used with iDEN modules

(GSM_ON=’0’ – iDEN module is on).

J9 –iO270 audio/PTT connector

Connector:

NELTRON 2417RJ-8-F4, 8-way 2mm header

Mating connector:

JST PHR-8

, 8-way 2mm housing, female

Mating crimps:

JST SPH-002T-P0.5S

Pin Signal

name

1 SPKR-

2 SPKR+

3 3V_OPT

4 VCC

5 GND

6 PTT

7 MIC-

8 MIC+

As viewed from the connector pins

Summary of Contents for ZEUS









































































































































Search results

Summary of Contents for ZEUS

Reviews:

Related manuals for ZEUS

Brands by name

Popular brands

Eurotech ZEUS, Technical Manual

Search results

Summary of Contents for ZEUS

Reviews:

Related manuals for ZEUS

Brands by name

Popular brands