Eurotech ZEUS Technical Manual Download Page 102

Page: 102 / 136

ZEUS Technical Manual

Appendix D - Reference information

102

Appendix D - Reference information

Product information

Product notices, updated drivers, support material, 24hr-online ordering:

www.eurotech-ltd.co.uk

EPIC information

Embedded Platform for Industrial Computing:

www.pc104.org/technology/PDF/EPIC_Spec_2.0.pdf

PC/104 Consortium

PC/104 Specifications - vendor information and available add on products:

www.pc104.org

USB information

Universal Serial Bus (USB) specification and product information:

www.usb.org

SDIO card information

SD Card Association and product information:

www.sdcard.org
www.sdcard.com

CompactFlash information

CompactFlash Association and product information:

www.compactflash.org

ZigBee information

ZigBee Alliance:

www.zigbee.org

Davicom Semiconductor Inc

Davicom DM9000A Ethernet Controller documentation:

www.davicom.com.tw/eng/index.htm

Summary of Contents for ZEUS









































































































































Search results

Summary of Contents for ZEUS

Reviews:

Related manuals for ZEUS

Brands by name

Popular brands

Eurotech ZEUS, Technical Manual

Search results

Summary of Contents for ZEUS

Reviews:

Related manuals for ZEUS

Brands by name

Popular brands