background image

Connectors, Switches, and Indicators 

 

29 

110124-7000A 

 

 

 

 

JP2:  Sleep/Wake 

Type:  2-post header, 2 mm 
 
Jumper JP2 acts as a sleep/wake button.  Momentarily short the pins of JP2 to transition to “sleep” or 

to “wake”.  This jumper also connects to the discrete control signal BTN_ONOFF# on pin 3 of header 

J9

, pag

30

. 

 

Setting 

Description 

NC 

Normal operation 

1-2 

Transitions the Vector to or from sleep mode 

JP3:  4-, 5-, or 8-wire Touch Panel 

Type:  2-post header, 2 mm 
 
Jumper JP3 configures the touch panel controller for 4-, 5- or 8-wire touch panels.  For further details 

about the touch panel, see 

Touch Panel Controller

, page 

19

. 

 

Setting 

Description 

NC 

4-wire or 8-wire (default) 

1-2 

5-wire 

Signal Headers 

The following tables describe the electrical signals available on the connectors of the Vector.  Each 

section provides relevant details about the connector including part numbers, mating connectors, 

signal descriptions, and references to related sections.  For the location of the connectors, see 

Identifying Connectors

, pag

27

. 

J3:  ITP Debug Port 

Board connector:  24-pin FFC/FPC connector, 0.5 mm, Molex 52435-2472 
 
Connector J3 provides an In-Target Probe (ITP) debug port for the Vector.  This port is not supported 

for application use. 

J4:  Stereo Speaker Output 

Board connector:  1x4 shrouded header, 1.25 mm, Molex 53398-0471 
Mating connector:  housing, Molex 51021-0400 
 
Header J4 provides a stereo speaker output.  For further details, se

Audio Interface

, pag

20

. 

 

Pin 

Name 

Type 

Description 

SPKR2+ 

Speaker 2 

SPKR2- 

SPKR1+ 

Speaker 1 

SPKR1- 

J5:  Stereo Line Out 

Board connector:  1x4 shrouded header, 1.25 mm, Molex 53398-0471 
Mating connector:  housing, Molex 51021-0400 
 
Header J5 provides a stereo line output.  For further details, see 

Audio Interface

, page 

20

. 

 

Pin 

Name 

Type 

Description 

LINEOUT_L 

Line out – Left channel 

LO_SENSE 

Line out sense 

LINEOUT_R 

Line out – Right channel 

GND_HDA 

Analog ground 

Summary of Contents for Vector














































Reviews: